Equipment for research

Custom research robots, experimental equipment, and measurement systems

Revot Co., Ltd. (株式会社revot) · University of Tsukuba spin-off · Shinjuku, Tokyo

Revot Co., Ltd. is a University of Tsukuba spin-off in Tokyo. Revot develops custom mobile robots, experimental equipment, measurement instruments, and data collection applications for university laboratories, research institutes, and corporate laboratories. Revot handles mechanical design, circuits, circuit boards, firmware, controls, and applications, starting from a single prototype. Proof-of-principle equipment starts at JPY 500,000, excluding consumption tax, with an estimated duration of 3 weeks–2 months. Revot delivers design data and source code with the equipment.

Inquiries in English are accepted by email at contact@revot.jp. The contact form on this site is in Japanese. Revot replies in English or Japanese.

Equipment designed around the experiment

Revot designs and builds equipment for measurements that commercial instruments cannot provide, repeated operation under specified conditions, and synchronized recording from multiple sensors. Each unit has specifications based on the research objective.

Projects typically involve one to several units. Revot prioritizes measurement capability, adjustable conditions, and later modifications over appearance. This service covers equipment used to conduct research. Development that turns research results into products falls under Revot's industry–academia collaboration and joint research services.

Development services for research laboratories

  • Mobile robots: ROS-based autonomous navigation, localization, path planning, obstacle avoidance, sensor integration, and implementation on the robot. Revot supports wheeled and omnidirectional drives.
  • Experimental equipment: Systems that operate motors or displays based on measured values.
  • Measurement instruments: Sensor selection, circuits, circuit boards, enclosures, and recording applications.
  • Wearable measurement devices: Circuits, enclosures, firmware, wireless communication, and designs for simultaneous operation of multiple units.
  • Research drones: Airframe design and fabrication, control software, and sensor integration.
  • LiDAR and point clouds: Data acquisition, noise removal, registration, and 3D reconstruction.
  • Data collection applications: iPhone, iPad, Android, and PC software.
  • Proof-of-principle prototypes: Equipment focused on testing a principle without appearance requirements.

Revot also accepts circuit-board-only or software-only work and adds sensors to existing robots or machines. Revot selects commercially available sensor elements and modules to suit the phenomenon and environment. Revot does not develop sensing elements themselves.

Raw data, synchronized measurements, and repeatable experiments

  • Measurement requirements: Revot documents the quantities to measure and evaluation conditions before design. Revot tests the equipment under those conditions before delivery and records the results in a test report.
  • Raw sensor data: Revot stores raw readings alongside processed results. The specifications define which values to record, recording intervals, and formats suited to the analysis software.
  • Time synchronization: Revot incorporates synchronization when experiments require comparison of data from multiple sensors or devices.
  • Adjustable conditions: Revot makes values such as speed, thresholds, and recording intervals configurable and documents them in a parameter list.
  • Future modifications: Revot delivers circuit diagrams, circuit board data, enclosure 3D data, a bill of materials, source code, a parameter list, and a test report with the equipment. The contract defines rights for modifications and additions.
  • Changing specifications: Revot first prototypes the most uncertain part, then uses the results to define the next development scope.
  • Operation near people: Revot defines stopping methods and conditions before building robots that operate near people. Revot develops safety stops alongside motor controls. For wearables, Revot selects skin-contact materials and structures that reduce injury risk if damaged.
  • Unpublished research: Revot treats consultations as confidential and can sign a nondisclosure agreement before discussions.

Completed projects and internal development

  • Delivered ROS mobile robot: Revot developed autonomous navigation, sensor integration, and implementation on the robot for a major construction consulting company. Revot verified operation on the physical robot before delivery. The intended use and specifications are not disclosed because of a confidentiality obligation.
  • Delivered measurement drone: Revot developed and delivered a compact, original measurement drone for a university or research institute whose name is not public.
  • Internal research drone: Revot assembles drones in-house for research and development, for autonomous flight indoors and underground where GPS does not reach. Its GNSS-free LiDAR drone has a measurement range of 0.5–40 m, a flight time of 10 minutes, 5-inch propellers, and 3D scanning.
  • SASSEN: Revot's LED swords contain four pressure sensors to detect strikes, with decisions accurate to 0.025 seconds. A single smartphone tallies the score.
  • Cyber KASSEN: Revot's wearable devices support up to 100 simultaneous participants per match. A proprietary Wi-Fi system synchronizes devices and automatically aggregates results. Revot has manufactured several hundred units.
  • Cyber Molkky: Sensors inside each pin detect when it falls, and an iPad automatically calculates scores. The system operates outdoors under changing sunlight, wind, and ground conditions.
  • Agricultural measurement system: Revot developed and delivered a system that predicts crop yields from drone imagery. The work covered imaging plans, drone operation, image analysis and prediction models, and an application for viewing the results.

Revot developed both the hardware and software for SASSEN, Cyber KASSEN, and Cyber Molkky. These products operate at national tournaments, school classes, and municipal events.

Estimated development costs and durations

All prices below are starting estimates, excluding consumption tax. Revot provides an initial estimate during the first consultation.

Development scopeStarting priceEstimated duration
Proof-of-principle equipmentJPY 500,0003 weeks–2 months
One prototype in a practical formJPY 1,500,0002–5 months
Small-batch prototypesJPY 3,000,0003–6 months
Measurement device prototypeJPY 3,000,0003–6 months
One wearable prototype, up to BLE connectionJPY 1,500,0002–4 months
Measurement and control systemJPY 3,000,0004–10 months
Development involving robots or autonomous mechanismsJPY 5,000,0006–12 months
Application connected to equipment or sensorsJPY 3,000,0003–8 months
LiDAR point cloud acquisition and processing demonstrationJPY 980,0001–3 months

Costs depend on hardware scope, unit quantities, operating conditions, simultaneous device operation, response requirements, wireless communication, and the use of existing components. Outdoor operation, dust, waterproofing, and locations without GPS increase verification work.

From consultation to delivery

  • Consultation: Revot discusses the research objective, quantities to measure, operating environment, deadline, and budget. The initial consultation is free.
  • Initial estimate and proposed configuration: Revot explains the estimated cost and duration and their basis, at no charge. For a fixed budget, Revot identifies essential functions and proposes a corresponding scope.
  • Specifications and formal quotation: Revot defines the equipment, measurement requirements, and evaluation conditions, then provides a quotation with an effort breakdown.
  • Checking uncertain parts: Revot uses a small prototype to check parts where it is unclear whether the measurement or operation will work.
  • Design, fabrication, and testing: Revot proceeds through prototype checks and requests customer review as development progresses.
  • Delivery: Revot hands over the equipment, design data, source code, and other agreed deliverables.

Information to include in an inquiry

  • Research objective, quantities to measure, required data resolution, and output format.
  • Indoor or outdoor environment, floor or ground conditions, GPS availability, and power supply.
  • Whether people will wear the equipment or the equipment will operate near people, and the number of units.
  • Existing equipment, sensors, software, or prototypes to use.
  • Budget, delivery deadline, and required document formats or addressees.
  • Plans for laboratory modifications or publication of the equipment's configuration in papers or conference presentations.

Undecided items can remain unspecified. Revot can propose a configuration and cost estimate from a description of the measurement or movement required.

About Revot and English inquiries

Customers that Revot can name publicly include the National Institute of Advanced Industrial Science and Technology, the University of Tsukuba, and the National Agriculture and Food Research Organization.

Revot's representative, Seita Sukisaki, holds a master's degree in engineering and an MBA from the University of Tsukuba and is enrolled in its doctoral program. The representative handles inquiries and technical decisions directly.

Revot accepts inquiries in English by email at contact@revot.jp. The contact form on the site is in Japanese. Revot replies in English or Japanese. Specifications, notes, and drawings can accompany an inquiry. Seita Sukisaki replies directly within 1–2 business days.

Frequently asked questions

Can Revot build just one custom unit?

Yes. Revot typically builds one to several units, with specifications tailored to each research purpose.

Can Revot prototype wearable sensors for research?

Yes. Revot develops circuits, circuit boards, enclosures, firmware, and recording applications using commercial sensors. For measurements lasting several days to several weeks, Revot designs devices to store data internally and transfer it in batches.

Can the laboratory modify the equipment after delivery?

Revot supplies design data and source code. The contract defines rights for modifications and additions. Transfer of rights can also be discussed.

Can Revot work toward a fixed delivery deadline?

Please tell Revot about any schedule constraints at the outset. Revot will then explain the scope that can be built by the deadline. If the full scope cannot fit, Revot proposes development in stages.

Can Revot provide a quotation for comparison with other suppliers?

Yes. Quotations are free. Revot can follow the institution's required formats and addressees for quotations and specifications.

Can payment follow inspection and acceptance?

Yes. Revot accepts payment by invoice after inspection and acceptance. Revot can also adjust specifications to the budget and discuss scheduling around institutional deadlines.

Contact Revot

Inquiries in English are accepted by email at contact@revot.jp; the contact form is in Japanese. Seita Sukisaki, the representative director, replies directly within one to two business days.

Email contact@revot.jp

Revot Co., Ltd. / 3-16 Ichigaya-Tamachi, Shinjuku-ku, Tokyo 162-0843, Japan

Contact form (Japanese)